🪆 Ford Focus Test Mode List

Early Ford Mode 6 also included misfire monitor test results, even though this monitor is classified as continuous. All vehicles using Controller Area Network (CAN) protocol have the misfire monitor results as well. In addition, CAN vehicles have improved Mode 6 with data screens already translated and converted into real data. The in.-H 2 O gauge will help you duplicate the test Ford is performing on the vehicle. With the evap test machine and/or in.-H 2 O gauge connected to the gas vapor system, engine running, the CVS deenergized (open) and the CPS energized (open), this should cause the in.-H 2 O gauge to go negative, approximately −2.0 to −4.0 in.-H 2 O. OBD II modes are: *Mode 1: Real-time data, MIL, IM monitors. *Mode 2: Freeze frame. *Mode 3: Stored DTCs. *Mode 4: Clear/Reset DTCs and emissions-related diagnostic information. *Mode 5: O2 monitoring tests, supported. *Mode 6: Test results for continuously and noncontinuously monitored systems, supported. *Mode 7: Pending DTCs. The SELECT/RESET button must be released within 3 seconds of TEST being displayed to ensure the Self-Diagnostic test mode can be continued. To scroll through the test mode data press the SELECT/RESET button once to advance each step through the data, eventually DTC data will be displayed, DTC should show 0 if no faults have been logged Park or Neutral Position Switch Out of Self-Test Range: Wiring, PNP switch/CPP switch, ECM: P1710: No Change In Transmission Fluid Temperature Signal: P1711: Transmission Fluid Temperature Sensor Out of Self-Test Range: Transmission not at normal operating temperature -repeat test: P1712: Trans Torque Reduction Request Signal Malfunction: P1713 Description. The PID mode allows access to powertrain control module (PCM) information. This includes analog and digital signal inputs and outputs along with calculated values and the system status. There are two types of PID lists available and both are used throughout this manual. The first is the generic (J1979) OBD PID list. In this video, I will show you how to get into test mode on recent Ford vehicles. Note that there is a mistake in the video, the DTCs reported are not OBD2, IIRC few of the instrument cluster codes are of much use. Reading codes through the OBD connection give you ones that will help more in std. format. Test mode data is often useful for monitoring/checking without tools, best use of this trick. ('04 thread, really an old one brought back) "Rubber Side Down". S.R. #275. When each button is pressed, the screen displays the button that is active. This test can also be used to isolate a stuck button. Radio Signal Strength : The ACM or FDIM displays the AM/FM antenna signal strength. To run this test, the audio system should be in AM radio tuner mode before entering the ACM self-diagnostic mode. HDD Test Estate 1.5L Ford EcoBlue 120PS Diesel 8 Speed Automatic FWD G 127 No 20,895.83 25,075.00 25,370.00 133.87 267.73. Ø The CO. 2. emissions test figures shown in the table are derived from the Worldwide Harmonised Light Vehicle Test Procedure (WLTP) . 5-seat mode, laden to seat back height (with tyre repair kit) 392 392 392 2-seat mode, laden to roof (with tyre repair kit) 1354 1354 1354 Fuel tank capacity (litres) Petrol 52 52 52 Diesel 47 47 47 Focus wagon Dimensions (mm) Titanium (inc. Vignale) Active (inc. Vignale) ST-Line (inc. Vignale) Exterior Ford Focus Service Manual Parameter Identification (PID) / Ford PID List. This is not a complete list of Ford PIDs available. This is a list of Ford PIDs in this manual. A/C Pressure Sensor Voltage. A/C Pressure Sensor Pressure. Accelerator Pedal Position 2. Maximum Difference between APP1 and APP2. Accelerator Pedal Position Mode. .

ford focus test mode list